954-804-1044

Hoppe Single Point Lock

Hoppe Single Point Lock

Hoppe Single Point Lock – Steps to take before ordering your replacement lock.

Step #1 – Find Your Backset

This illustrates the proper way to measure an HLS-9000 backset on a Hoppe Multipoint door lock.

Step #2 – Find Your Dead Bolt Throw

This illustrates the proper way to measure an HLS-9000 deadbolt throw on a Hoppe Multipoint door lock.
Measure your existing Single point lock and determine the “Back Set”. The back set is the measurement of the distance from the edge of your door to the center of the handle. The only backsets available from Hoppe are:
  • 35mm or 1 3/8 Inches
  • 45mm 0r 1 3/4 Inches (The Most Common Backset)
  • 60mm or 2 3/8 Inches
  • 70mm or 2 3/4 Inches
You will need to know the “Deadbolt Throw” distance. This is the measurement  of how far the deadbolt extends out of the single point mortise lock. Open the door, Activate the lock by lifting upward on the handle. Turn the thumb turn knob and extend the deadbolt. Hoppe only has (2) deadbolt options to choose from.
  • 14 mm or 1/2 Inch – Available on 35mm and 45mm Backsets
  • 25mm or 1 Inch – Available on all backsets

Once you know the “Backset” and “Deadbolt Throw”, You should be able to find the proper Single Point Lock below

Below are the available options for Single Point Locks. Please select your lock below and click on the link, you will be taken to the product page of the lock you have selected. There you can read the specifications and purchase your lock replacement. Locks are separated into available backsets first, then by deadbolt throw measurements.

Hoppe single point lock replacement

Hoppe Single Point lock. This lock only locks at a single point, the deadbolt.

35mm Backset

35mm (1 3/8″) Backset, 14mm (1/2″) Deadbolt Throw

35mm (1 3/8″) Backset, 25mm (1″) Deadbolt Throw

45mm Backset

45mm (1 3/4″) Backset, 14mm (1/2″) Deadbolt Throw

45mm (1 3/4″) Backset, 25mm (1″) Deadbolt Throw

60mm Backset

60mm (2 3/8″) Backset, 25mm (1″) Deadbolt Throw

70mm Backset

70mm (2 3/4″) Backset, 25mm (1″) Deadbolt Throw

Hoppe Part Number Lock Type Locking Point Backset Dead Bolt Throw Hoppe Description
11517463 Single Point Dead Bolt 35mm (1.38) 14mm (.55) M/35/14 / 16-RC / W-SPERR
11517487 Single Point Dead Bolt 45mm (1.75) 14mm (.55) M/45/14 / 16-RC / W-SPERR
11517475 Single Point Dead Bolt 35mm (1.38) 25mm (1.00) M/35/25 / 16-RC / W-SPERR
11517499 Single Point Dead Bolt 45mm (1.77) 25mm (1.00) M/45/25 / 16-RC / W-SPERR
11517505 Single Point Dead Bolt 60mm (2.36) 25mm (1.00) M/60/25 / 16-RC / W-SPERR
11517517 Single Point Dead Bolt 70mm (2.75) 25mm (1.00) M/70/25 / 16-RC / W-SPERR

One of the most common mistakes customers make when buying a replacement lock is simply by not choosing the correct measurement. If you take a little time and measure the lock correctly, you should be able to find the exact lock that you need. Another mistake that is commonly make is that customers buy a single point lock to repair a broken multipoint lock. This will not work since the 2 lock types are not the same.

A multipoint lock has an internal slide bar that transfers motion onto connected lock extensions while a single point lock does not. A single point lock does not work as a multipoint gearbox replacement. Below are some indications that your lock may have internal parts that are broken.

  1. Door is stuck or jammed and cannot be opened

  2. Lever handle is sagging or drooping and not returning to the horizontal rest position after the door has been opened.

  3. Lock seems to be stripped when opening the door. internal gear teeth are slipping and not disengaging the lock points.

  4. Lock makes a crunchy noise when opening or locking the door.

  5. Unable to activate the deadbolt after lifting up on the handle.

error: Alert: Content is protected !!